Select Page

With the boat ashore, here are some recommendations for carrying out a boat owner electrics inspection. Safety is always paramount so remember to do the checks with the batteries off. Wearing a head torch helps, make notes as you go and only tackle a repair if you are 100% sure you know what you are doing:

Wiring checks

  • Labelling – the idea of labelling where each wire connects to and from may sound time consuming but will pay dividends when you or your electrician need to source a component’s wiring in a hurry. Being organised here will really be of help and save you money in the long run.
  • Wiring diagram – refer to your boat’s wiring diagram as you carry out the inspection. If you don’t have a schematic of all the boat’s equipment and wiring plan, then it would be a good idea to sketch one out. This will also be invaluable when troubleshooting faults.
  • Chafing – check the condition of the wiring for any signs of chafing, or exposed wires. This can be caused by vibration of wires that are not properly secured rubbing against things or where wires pass through bulkheads. This happens when wire are not properly protected by conduit and suitable grommets or have come into contact with sharp objects. At very worst protect with electrical tape, but exposed wiring should be replaced with new marine grade wire as soon as possible. Also at the same time you will need to fit suitable conduit, grommets or padding.
  • Melted wires – wires that overheat are a serious fire risk and need to be sorted out as a priority. Look for signs of melted wiring insulation, caused either by overloaded wires becoming very hot or from being in contact with a hot engine. Ensuring wires don’t come into contact with hot engines is easy enough to fix. However, wires that overheat need some troubleshooting to determine the cause. This might entail replacing with thicker wire to suit the power draw of the components they connect to and/or protecting with more appropriate fuses (see below). If in any doubt this is time to call in professional help.
  • Fuses and circuit breakers – fuses need to be rated lower than the wires they are protecting and lower than the components they connect to. Check all wires are protected by a fuse or circuit breaker.
  • Connections – check the wiring for weak connections, tighten or replace any that are loose and check for corrosion. Poor connections that are not properly installed or corroded are also fire hazards. Note: do not use electrical tape to repair a connection.

boat electrics

Battery checks

  • Battery connections – check the condition of the battery connections. Check for tightness. Clean and coat with petroleum jelly.
  • Battery straps – check the batteries have remained secure and the retaining straps are in good condition and have not become weakened.
  • Battery top up – unless they are maintenance-free type, check battery levels and top up with distilled water if necessary.
  • Battery condition – test batteries to confirm capacity. Check batteries are kept clean and dry. If the boat is ashore over the winter, consider taking the batteries home for storage as they will last longer. Note – I have done this for the past 7 years with my current batteries and they are still in good condition

Alternator checks

  • Belt tension – check the belt tension. This should be enough to allow the belt to be depressed by 12mm or so when pushed down by the thumb.

Equipment checks

  • Navigation lights – check all navigation lights are working correctly. Make a note of any bulbs that need replacing and add to the to do list. The most likely causes of a bulb failure are either that it is blown or the contacts have become corroded. Masthead lights can suffer from voltage drop as there is a long cable run from the battery to the top of a mast and resistance in the wire can become excessive. Consider replacing with thicker wire if this is the case. Corrosion of the bulb contacts and connections need to be checked and cleaned up first, using fine emery paper. Also check deck connectors are in good condition. Also check lens seals are in good condition and are not allowing ingress of water into the light.
  • Exterior bulbs – clean exterior bulb contact points, including deck lights. Spray with anti-corrosion spray.
  • Interior lights – check all interior lights are working. Make a note of any bulbs that need replacing and add to do list.
  • Bilge pumps – check the float switch and manual override switch of the bilge pumps are working correctly. If not, check the connections and fuse leading from the battery to the pump. Note a bilge pump is one of the only pieces of equipment that should be wired directly to a battery via its own fuse to ensure it will work if the batteries are turned off.
  • Instruments – test all the instruments are working satisfactorily and carry out any annual maintenance recommended by the manufacturer’s operator manual. Clean instrument screens with plasma screen cleaner.
  • Solar panels – check electrical connections are in good order and secure.

Boat surveys

A full boat survey assesses the condition of the hull, mechanical gear and means of propulsion. The survey is carried out with the boat...

Marine toilets – care and maintenance

There are a number of different types of marine toilet, or heads. They fall into one of three categories – manual, electric and vacuum, the most common being the manual, hand pumped type. These have double acting piston-pumps which both discharge the waste and flush the toilet with sea water.

Capsize – understanding the risks

A skipper should know how their boat will cope with rough seas. By working within known limits and understanding the risks,...

ColRegs when sailing single handed

  Don’t neglect the Colregs when sailing single handed Sailing single-handed represents several challenges for skippers, not least how to...

First Aid Afloat – fish spine injury

First Aid Afloat - Here is what to do if somebody stands on a fish spine: • Check for dangers. Is it safe for you to enter...

Passage Planning Advice & Safety for skippers

Passage planning helps you to: • Decide where to go • Calculate how long it will take to get there • Avoid bad weather •...

Saildrive maintenance

There are less maintenance tasks to carry out on a saildrive transmission than on a traditional inboard shaft drive system with its associated stern gear. However, there are a few critical things that require maintenance, as recommended in detail by the engine manufacturers, and should be adhered to.

Cutless bearing replacement

Cutless bearings can last for many years but if the propeller shaft is out of alignment they will wear through more quickly. If you have noticed a clunking sound when motoring then it could be a worn cutless bearing that is causing the problem.

How diesel engines work

The basic principle of a diesel engine is less complex than that of a petrol engine. No spark plug or ignition system is needed, making the basic diesel engine a comparatively straightforward system that results in fewer faults and has lower maintenance costs than a petrol engine.

Leaking decks

Leaking decks are perceived as a nuisance by some boat owners, but if leaks are ignored a much more serious situation may well be developing, especially in the case of boats with balsa or plywood deck cores. So deck leaks do need to be investigated and dealt with.

Boat ownership – some fundamentals

Owning a boat is a big commitment that should bring no end of satisfaction, but the costs of maintaining and keeping a boat are significant and should never be underestimated.

Antifouling for leisure boats – Part 3

Antifouling is one of the least pleasant boat maintenance jobs to do, but it has to be done. The very worst job of all is removing the old antifouling as this can get seriously messy and is very hard work.

What boating skills should you have before you buy a yacht?

Many people dream of owning a yacht and sailing off into the blue yonder. What boating skills should you have before you buy...

Always have an emergency grab bag to hand when at sea…

  Grab bag: In the event of having to abandon ship, it is recommended to have a designated waterproof bag to carry...

Marine engine electrical system

The typical basic electrical system associated with a marine engine includes a dedicated engine starting battery, a starter motor, a charger in the form of an alternator, a solenoid and some engine sensors and instruments.

Jester Challenge 2022 – Sailing single handed from Plymouth UK to the Azores: Getting to the Start

Jester Challenge – A modern experiment in old-fashioned self-reliance, self sufficiency, and personal responsibility. This is the start of a 10-part post where solo sailor, Bernie Branfield, shares his first hand account of his single-handed, 2022 Jester Challenge, from Plymouth, UK to the Azores, in his 26′ Invicta Mk2, Louisa.

How a propeller works

Have a look around any boatyard and you will notice quite a variety of propellers – some have two blades, some have three and others have four or more. While most propellers are completely rigid some have blades that fold.

Sail care and maintenance – Part 1

When thinking about the care, maintenance and repair of sails it helps to have some understanding of the properties of the ever growing range of modern sailcloth and the fibres they are made from, as opposed to the traditional canvas sails of the past.

Tips and advice for staying safe on a sailboat at sea

Here we focus on how to stay safe on a sailboat at sea. We cover key things to ensure you have on board before you set sail as well as covering the most common cause of incidents on sailboats and how to deal with them.

Common marine electrical problems

Most problems with marine electrical systems arise from four possible sources, a lack of maintenance, a poor standard of initial installation, insufficient battery capacity, or ineffective charging systems.
Water ingress is a frequent issue – salt water can corrode contacts very quickly. If connections are not scrupulously clean – or are loose – resistance will be increased, resulting in progressively reduced power.

Essential Knots: Clove hitch

Essential Knots: Clove hitch Use: Tying a rope to posts, bollards, rings or a guardrail. Step 1. Make a turn around the object and lay...

Electric motors and hybrid systems

In recent years there have been considerable advances with the development of electrically powered propulsion in the leisure marine sector. This includes developments with inboard and outboard electric motors, hybrid systems, lithium-ion battery technology as well as solar, wind and hydro powered generators.

Wooden Hull Repairs

While wooden boat hull maintenance is mostly straightforward, it is always a good idea to take expert advice on any repair job needed doing to a wooden boat, unless you have done the job before and know what you are doing.

Boat Engine Safety Checks

  Boat Engine Safety Checks Every skipper needs to make regular essential boat engine safety checks. Below you will...

Understanding your mast and rigging

The rig of a sailing boat is put under huge stresses and strains so it is important for inspections of a yacht's spars and rigging to be...