Select Page

Essential yacht tender safety

Essential yacht tender safety – the dangers inherent in using a dinghy to get ashore from a moored or anchored yacht are all too easily underestimated.

A recent experience caused me to have a serious think about essential yacht tender safety. Recently I faced the prospect of coming ashore from my mooring in the pitch dark, in wet, breezy conditions with a strong tide running, over a distance of about 300 metres. I was by myself and it prompted me to ask myself before setting off whether it would be unsafe to use the tender or should I spend the night on board?

Consider your options

Yes, the driest and safest option would have been to stay on board, but I had my wet weather gear and a lifejacket, I hadn’t been drinking and I was confident that my little Zodiac inflatable was up to the job. OK, if the outboard packed up then it would be a challenging row against the fast running tide.  However the tide was coming in so I wouldn’t be swept out to sea and, with wind against tide, there were going to be sharp little waves to contend with.

I decided to go for it and quickly got completely soaked by the spray, as did the gear. Finding my way through the boats on their swinging moorings in the pitch darkness was a challenge.  I was greatly reassured to have my truly excellent Exposure Marine X2 torch. I would urge all those who use a tender to buy one – expensive but worth every penny. They are waterproof, lightweight and incredibly powerful.

There are inherent risks in most boating activities and this includes using a yacht tender to get ashore from a mooring or anchorage. After last week’s soaking, I have compiled some hints and tips about essential yacht tender safety – see below.

Essential yacht tender safety

Essential yacht tender safety :

  • Plan ahead and make notes of the tide state and weather forecast for when you set out and expect to return from a trip.
  • Wear lifejackets, even for short trips.
  • Wear a killcord, even for short trips.
  • Carry oars as back up in case the outboard fails.
  • Carry a means of communication – mobile phone in a waterproof cover or a handheld VHF.
  • Carry a lightweight, powerful, waterproof torch (see above).
  • Don’t overload the dinghy – follow the manufacturer’s recommendations.
  • Carry a foot pump.

Essential yacht tender safety

Essential yacht tender safety – other considerations:

  • Use bow and stern lines to secure the dinghy alongside – much easier to get on and off.
  • Always check you have enough fuel – you can easily be caught out.
  • Keep a puncture repair kit ashore and on the yacht – otherwise you can guarantee when you need it it will be in the wrong place.
  • Keep spare killcords ashore and on the yacht – they have a habit of disappearing.
  • Keep spare valves for tube inflation points.

Essential yacht tender safety – outboard care:

  • Make sure your outboard complies with dinghy manufacturer’s recommendations.
  • Service the engine every season.
  • Attach a lanyard to prevent the outboard going over the side (I didn’t in the past – very costly).
  • Flush the engine in fresh water after use in salt water.
  • Keep spares including a spare spark plug, shear pins (essential) and kill cord.

Essential yacht tender safety – choosing an inflatable dinghy:

  • Storage is a big issue, especially on a yacht. Check weight and dimensions before buying.
  • Consider how easy or difficult it will be to lift an inflated dinghy aboard.
  • Storage will most likely affect capacity. 2 or 3 person inflatables are usually adequate.
  • There are many types to choose from. Check what works best for your yacht.
  • Consider different types of floor – slatted or inflated. Solid floors make standing up easier and are better for carrying gear.
  • Solid transoms are best for outboards, but bulkier.
  • Check the inflatable has well designed oar rowlocks – not all do.
  • Hypalon coated tubes are more expensive and better quality than PVC coated nylon.

 

 

How to tackle osmosis

Many owners of old GRP boats live in fear of osmosis, but what exactly is osmosis and what can be done about it? Osmosis comes about...

Antifouling for leisure boats – Part 2

To prepare for antifouling, as soon as your boat has been lifted out and pressure washed, you need to check all the surfaces of the hull below the waterline, remove any remaining barnacles and check for blisters.

An explanation of the IALA maritime buoyage systems – IALA A and IALA B

What are the differences between the two IALA buoyage systems, IALA Region A and IALA Region B, and where are they used?   As recently as the 1970s...

Gybing a sailing boat

Gybing is the sailing manoeuvre used to change a boat's direction through a following wind. As with the tacking manoeuvre,...

Estimating and plotting your position at sea

This post covers how we go about estimating and plotting our position using traditional methods, when out of sight of land – covering Dead Reckoning, Estimated Position, Tidal Streams, Leeway and more…

VHF DSC radio – how best to communicate at sea

There are many ways to communicate with others at sea. What makes the VHF DSC radio the best form of short range...

The dangers of running aground in a motor boat

The peril of grounding a motor boat is not only an inconvenience; it can lead to substantial risks for both the vessel and its passengers. . In this article, we’ll explore the potential dangers of running aground and highlight the importance of proper navigation and preparedness to avoid these hazards!

Narrowboating on the Kennet and Avon Canal

A recently cancelled sailing event I was due to take part in left us with a free weekend in the diary. Given that my wife and I were celebrating a bumper wedding anniversary and the weather forecast was for fine weather, we decided to hunt around for a last minute canal holiday.

Repairing chips and dings in gelcoat

The gelcoat topsides of a GRP boat can be pampered and restored to their former glory relatively easily when it is ashore. Gelcoat is only a very thin outer layer of the hull, often less than 1mm thick, so you should avoid cleaning it with highly abrasive cleaners, or an-ything that could potentially damage its surface.

The Round The Island Race 2023

This year’s Round the Island Race turned out to be a really thrilling and competitive event. 1100 boats entered the race, which took place on Saturday 1st July. The race started from the world famous Royal Yacht Squadron line in Cowes UK, with the largest and fastest boats starting first, leaving the rest of us to wait our turn.

Boat plumbing maintenance & troubleshooting

A boat’s fresh water system needs annual maintenance to keep it in good condition. Some boats have far more complex systems than others, with pressurised hot and cold water, associated pumps, an accumulator, calorifier and pressure valves, all to keep a boat owner busy.

Jester Challenge 2022 – Sailing single handed from Plymouth UK to the Azores: Part 3 – Preparations

Jester Challenge – A modern experiment in old-fashioned self-reliance, self sufficiency, and personal responsibility. This is the third of a 10-part post where solo sailor, Bernie Branfield, shares his first hand account of his single-handed, 2022 Jester Challenge, from Plymouth, UK to the Azores, in his 26′ Invicta Mk2, Louisa.

Antifouling for leisure boats – Part 3

Antifouling is one of the least pleasant boat maintenance jobs to do, but it has to be done. The very worst job of all is removing the old antifouling as this can get seriously messy and is very hard work.

Docking a Motorboat

Docking a motorboat can be a challenging task, especially for beginners, but with practice and attention to detail, it becomes much easier. Here’s a step-by-step guide to help you dock your motorboat safely and efficiently.

Boat surveys

A full boat survey assesses the condition of the hull, mechanical gear and means of propulsion. The survey is carried out with the boat...

Propeller care and maintenance

Propellers are complicated and repairs should be done by specialists but owners can carry out checks and some routine maintenance themselves when the boat is in the boatyard. A propeller is critical to a boat’s performance, fuel consumption and ride, so it makes sense to keep a propeller in good working order.

Jester Challenge 2022 – Sailing single handed from Plymouth UK to the Azores: Part 10 – The Return Trip

Jester Challenge – A modern experiment in old-fashioned self-reliance, self sufficiency, and personal responsibility. This is the final instalment of a 10-part post where solo sailor, Bernie Branfield, shares his first-hand account of his single-handed, 2022 Jester Challenge, from Plymouth, UK to the Azores, in his 26′ Invicta Mk2, Louisa.

Boating Rules of the Road – International ColRegs

    International ColRegs Rule 7: Risk of Collision Anyone who is responsible for a vessel at sea, from the...

Crew Overboard Drill – Updated

How to respond to crew overboard A Man Overboard (MOB) drill is a crucial safety procedure that every boater should practice regularly. It simulates...

Understanding tides

If you are used to sailing in tidal waters, you will know that tides can be both a benefit and a hindrance to the sailor. In many ways,...

Rig check – how to prevent failure at sea

Regular rig checks prevent the risk of mast and rigging failure at sea. This includes regular rig inspections of the spars, ...

Boat electrics

All boat owners should have a basic knowledge of electrics, both to avoid encountering electrical problems at sea and to stand a chance of solving them should they occur.

Passage Planning Advice & Safety for skippers

Passage planning helps you to: • Decide where to go • Calculate how long it will take to get there • Avoid bad weather •...

Cleaning & polishing painted topsides

The gelcoat topsides of a GRP boat can be pampered and restored to their former glory relatively easily when it is ashore. Gelcoat is only a very thin outer layer of the hull, often less than 1mm thick, so you should avoid cleaning it with highly abrasive cleaners, or an-ything that could potentially damage its surface.

Jester Challenge 2022 – Sailing single handed from Plymouth UK to the Azores: Part 5 – Boat Management

Jester Challenge – A modern experiment in old-fashioned self-reliance, self sufficiency, and personal responsibility. This is the fifth of a 10-part post where solo sailor, Bernie Branfield, shares his first hand account of his single-handed, 2022 Jester Challenge, from Plymouth, UK to the Azores, in his 26′ Invicta Mk2, Louisa.