Select Page

Preparing for a sailing trip entails a lot of planning. In this blog, we take a look at some of the many safety aspects that a skipper needs to consider before heading off on a cruise.

The degree of preparation, knowledge and equipment needed for cruising will vary considerably, depending on type of sailing you have planned. Fine summer afternoons pottering around sheltered home waters are naturally less onerous than planning a long distance cruise or even heading offshore and crossing oceans.

Inshore cruising

At a basic level there’s still much common ground with all types of cruising, whether shorter inshore trips or longer offshore voyages.

For example a yacht may be knocked down by a breaking wave when close to shore, and if heavy items such as tools, batteries, ground tackle and tins of food are allowed to move around in rough conditions they can damage either the vessel or crew members. Similarly, losing a washboard in heavy weather could spell disaster, so attaching them to the boat with a lanyard makes sense, and the companionway should be capable of being secured from above and below deck. Anyone who doubts the need for this should remember that the overfalls that form off coastal headlands have the potential for breaking waves that will lay a capable vessel on her beam ends.

Longer voyages

A boat undertaking a longer voyage will also need to be equipped to be self sufficient, potentially for long periods of time, with the spares and tools to undertake significant maintenance when necessary. It will also need a higher level of equipment – including first-rate ground tackle that will hold in a gale, plus heavy weather and storm sails.

At least two bilge pumps are needed, including, one that can be operated from below and a second that can be operated on deck, with all cockpit lockers closed. An emergency tiller should also be provided in case the regular one breaks (easily done if someone falls against it in heavy weather) or the wheel steering system fails. In both cases make sure you know how they are fitted – this is not something you want to be trying to figure out on a black night two miles off a lee shore in a rising gale.

Total rudder loss is also something that must be prepared for in advance. Offshore racing regulations, for instance, require crews to have tried at least one method of steering their boat without the rudder and cruisers ought to follow suit.

Many of the hard-won lessons of the ill-fated 1979 Fastnet Race are just as applicable today, as is this profound advice from the official inquiry report into the race: “In the 1979 race the sea showed that it can be a deadly enemy and that those who go to sea for pleasure must do so in full knowledge that they may encounter danger of the highest order.” Although both weather forecasting and the boats we sail have improved enormously in the past few decades, it would be complacent to assume that a storm of equal intensity could not ravage a yacht on a passage of more than a two or three days.

The human factor

Whether on an afternoon’s sail that turns into an unexpected upwind slog, a 60 mile crossing of the English Channel, or a five day crossing of the Bay of Biscay, there’s arguably more chance of the human factor being the weak link in the chain than problems with the boat.

The skipper and crew need to carefully pace themselves physically to keep functioning, with adequate food, drink and rest. In particular it’s worth remembering that sleep deprivation quickly leads to severely impaired capacity for flexible and innovative thinking, exaggerates tendencies to take risks, and reduces motivation. Equally, we are not able to function effectively for long periods of time without proper nutrition – even on day sails.

Finally, it’s worth having a plan to feed everyone on board, plus always carry further additional supplies of food and water in case the passage takes longer than expected.

Steel and Aluminium Hulls

The two metals used for hull construction are steel and aluminium. These are both very strong materials and will last a long time as long as they are cared for, which primarily means protecting steel boats from rust and aluminium boats from electrolytic action.

ColRegs – avoiding collisions at sea

ColRegs - avoiding collisions at sea ColRegs Rule 8: Action to avoid collision (a) Any action taken to avoid collision shall...

ColRegs when sailing single handed

  Don’t neglect the Colregs when sailing single handed Sailing single-handed represents several challenges for skippers, not least how to...

Fire safety advice at sea from the Marine & Coastguard Agency

Fire safety advice for boaters Top fire safety advice at sea: 1. Fit smoke alarms, carbon monoxide and gas detectors 2. Turn...

Hourly Checks when sailing or motoring

  Hourly Checks Get into the habit of carrying out these checks and both yourself, your crew and your boat will be...

The VHF DSC Radio jargon buster

AIS - Automatic Identification System This system is used by shipping. It allows another vessel or coast station to use...

Estimating and plotting your position at sea

This post covers how we go about estimating and plotting our position using traditional methods, when out of sight of land – covering Dead Reckoning, Estimated Position, Tidal Streams, Leeway and more…

Common marine electrical problems

Most problems with marine electrical systems arise from four possible sources, a lack of maintenance, a poor standard of initial installation, insufficient battery capacity, or ineffective charging systems.
Water ingress is a frequent issue – salt water can corrode contacts very quickly. If connections are not scrupulously clean – or are loose – resistance will be increased, resulting in progressively reduced power.

Boat Handling – anchoring

Anchoring your yacht or motorboat Anchoring is one of the most important boat handling skills. If you can set an anchor...

Is Boating Good for Your Health and Happiness?

Absolutely! Boating offers a wealth of benefits for both your physical and mental well-being, making it a fantastic activity for overall health and...

Keel design – options to consider when choosing a yacht

Keel design is constantly evolving and nowhere is this more apparent than in modern racing yachts such as the Imoca Open 60 class. These fast...

Essential Boat Safety Briefing

Skippers Responsibilities Skippers are obliged to give a safety briefing to the crew even if they are a regular crew. At...

Tips and advice for staying safe on a sailboat at sea

Here we focus on how to stay safe on a sailboat at sea. We cover key things to ensure you have on board before you set sail as well as covering the most common cause of incidents on sailboats and how to deal with them.

Going aground – what to do if it happens to you

When a yacht runs aground, it can be a stressful situation, especially on a falling tide in an exposed position with a swell running. There are several steps you can take to address the situation in order to ensure the safety of your vessel and its occupants. Here are some tips should this happen to you.

2023 Rolex Fastnet Race – Part 2

Simon Jollands took part in the 2023 Rolex Fastnet Race. This is the second of his articles on the race aboard Lancelot II, a Beneteau First 40.

Crew Overboard Drill – Updated

How to respond to crew overboard A Man Overboard (MOB) drill is a crucial safety procedure that every boater should practice regularly. It simulates...

Sailboat rig checks – Part 1

Sailing boat rigs need to be checked regularly to reduce the risk of rig failure at sea. In part one of Sail boat rig checks we run through a series of useful checks that owners and skippers can carry out.

Wooden Hulls – Part 1

Traditional wooden boats have a plank on frame construction, a centuries old boat building method that is still in use today. Variations of the traditional method include carvel, clinker and strip planking, which all relate to the way the planking is attached to the frame.

Estimating your position at sea

Navigators use a combination of techniques to estimate their position at sea. The primary method used today is GPS (Global Positioning System), a network of 24 satellites that became fully operational in the 1990s and was originally restricted for use by the United States military.

Passage planning and pilotage

Passage planning and pilotage help skippers navigate safely from one port to another. A passage plan takes into account all...

Repairing chips and dings in gelcoat

The gelcoat topsides of a GRP boat can be pampered and restored to their former glory relatively easily when it is ashore. Gelcoat is only a very thin outer layer of the hull, often less than 1mm thick, so you should avoid cleaning it with highly abrasive cleaners, or an-ything that could potentially damage its surface.

Boat Improvements

My Boat - practical improvements Author - Mike Rossiter Most boat owners who have had their craft for any length of time will have made what they...

Tacking a sailing boat

Tacking is the sailing manoeuvre used to change a boat's direction through an oncoming wind. Tacking a sailing boat calls for the crew to work as a...

Marine engine oil system maintenance

The regular maintenance of a marine diesel is key to preventing engine failure at sea. This means doing regular checks of the fuel, cooling, electrical and oil systems.

Marine diesel exhaust checks

You should inspect the exhaust system for corrosion damage regularly, especially around the injection bend. If you have noticed the engine exhaust smoking a lot during the sailing season this can also indicate a number of potential problems.