The give-way hierarchy

Who gives way to who at sea?

Even seasoned sailors sometimes get this wrong and in a crowded harbour this can easily lead to a collision or at best considerable embarrassment for a boat that mistakenly thinks it has right of way over another.

I recently went sailing with friends over a busy weekend on the South Coast of England. The conditions were perfect for sailing, a Force 4 breeze, full sunshine and everyone was out to enjoy themselves. While the conditions were perfect, Chichester Harbour was crowded with dinghy sailing races, keelboats, yachts, kayakers, paddle boarders, fishing vessels and countless motor boats of all sizes.

As we sailed towards the harbour entrance the crowding intensified and we kept a constant lookout in all directions. With a full genoa set, it was easy enough to keep a lookout to windward, but to leeward there is a significant blind spot for the person on the helm, so we decided to have a crew member at the bow to keep an all round lookout.

There was quite a bit of discussion about which vessels had right of way over others, so this has prompted me to produce a basic reminder of the give way hierarchy between sailing boats and power boats, plus explanations of what is meant by the give-way vessel, stand-on vessel and the overtaking rule.

Power boat gives way to sailing boat.
Sailing boat gives way to boat engaged in fishing.
Boat engaged in fishing gives way to vessel with restricted ability to manoeuvre.
Vessel with restricted ability to manoeuvre gives way to vessel not under command.
Note: A sailing boat which is motor sailing does not have priority over a power boat, even if it has sails hoisted.

Sailing boat hierarchy

Port tack gives way to starboard tack.
If on the same tack, the windward boat gives way.
If it is unclear to a sailing boat on port tack which tack another sailing boat to windward is on, then the boat on port tack must give way.

Power boat hierarchy

If two power boats are heading towards each other, both boats should alter course to starboard, so their port sides will pass each other.
If two power boats are crossing paths and there is a risk of collision, then the vessel which has the other on its starboard side must give way. It must also avoid crossing ahead of the stand-on boat.
If a power boat meets another head on and is not quite sure if a collision is likely, then it should assume it does and alter course to starboard.

Give-way vessel

When two similar vessels are crossing, the one that has the other to its starboard side is the give-way vessel.
The ‘give-way’ boat is responsible for keeping clear and altering course where necessary to avoid a collision.
The give-way boat should make an obvious course direction in plenty of time, so the stand-on vessel is in no doubt it has taken avoiding action.

Stand-on vessel

If you are the stand-on boat, keep to your course and speed to make it easier for the give-way boat to manoeuvre out of your way.
If the give-way vessel does not take avoiding action, the stand-on vessel must be ready to turn quickly out of the way or stop as a last resort.

Overtaking

All vessels, whatever their size and type, must keep well clear of others when overtaking.
It is courteous to overtake a sailing boat on their leeward side, so as not to take their wind.
The vessel being overtaken must maintain its course and speed.
The overtaking vessel must be well clear of the other before it can resume its original course, allowing the overtaken vessel to maintain its course throughout the manoeuvre.

A vessel is said to be overtaking another if it is approaching more than 22.5º behind the other vessel’s beam. This overtaking sector covers an arc of 135º, which is the same as the arc of a stern light. At night, it is easy to tell if you are overtaking a vessel because you can see its stern light as you approach it.

During the day, it is not always as easy to be sure you are in the overtaking sector. Are you overtaking or alternatively are you crossing the other vessel’s path, in which case you could have right of way? If in doubt, it is always best to proceed with caution and keep well clear of the other vessel.

Summary

Keep a lookout at all times.
Remember to follow the give-way hierarchy. Vessels with priority over you have the right of way.
When altering course, make sure that the new course does not result in another close-quarters situation.
Be prepared to reduce speed if you are the give-way boat.

Finally, in a very crowded harbour situation it is wise for sailing boats with engines to furl their sails and proceed under engine until they are clear of the harbour entrance. This is not a rule as such in most harbours but it makes sense and is what we decided to do until we had left the harbour.

Docking a Motorboat

Docking a motorboat can be a challenging task, especially for beginners, but with practice and attention to detail, it becomes much easier. Here’s a step-by-step guide to help you dock your motorboat safely and efficiently.

Care of boat batteries

Boat batteries need to be kept properly charged, which means never allowing the batteries to discharge below 50 per cent of their total charge. As well as the batteries themselves, keeping a boat’s charging systems in good shape will also help to keep batteries topped up to a higher level of charge.

Learn ColRegs: Traffic Separation Schemes

Learn ColRegs Rule 10: Traffic Separation Schemes. (c) A vessel shall, so far as practicable, avoid crossing traffic lanes...

How a propeller works

Have a look around any boatyard and you will notice quite a variety of propellers – some have two blades, some have three and others have four or more. While most propellers are completely rigid some have blades that fold.

Sailing & Motoring in Fog

Sailing & Motoring in Fog You can only measure the visibility accurately if sailing & motoring in fog when you have...

Sailing into a storm

Weather forecasting has become increasingly accurate, but despite this, I was caught out recently by a forecast that considerably underestimated the wind strengths and consequently was sailing single handed in to a Force 8 gale, which proved to be challenging!

Wooden Hull Repairs

While wooden boat hull maintenance is mostly straightforward, it is always a good idea to take expert advice on any repair job needed doing to a wooden boat, unless you have done the job before and know what you are doing.

Essential Knots: Clove hitch

Essential Knots: Clove hitch Use: Tying a rope to posts, bollards, rings or a guardrail. Step 1. Make a turn around the object and lay...

How to Avoid Collisions At Sea With The ColRegs

Every Skipper Needs Accurate Knowledge of the IRPCS ColRegs As a responsible skipper it is every skipper’s duty to learn and apply the IRPCS...

Points of Sailing

The course on which a boat is sailing can be described by its angle to the wind, not to be confused with its compass...

Sailboat rig checks – Part 1

Sailing boat rigs need to be checked regularly to reduce the risk of rig failure at sea. In part one of Sail boat rig checks we run through a series of useful checks that owners and skippers can carry out.

Saildrive maintenance

There are less maintenance tasks to carry out on a saildrive transmission than on a traditional inboard shaft drive system with its associated stern gear. However, there are a few critical things that require maintenance, as recommended in detail by the engine manufacturers, and should be adhered to.

Sailboat rig checks – Part 2

In part two of Sail boat rig checks we run through some useful rig maintenance tips and then finish with a brief look at what a professional rig check involves.

Navigating the Unknown: Boating in Limited Visibility

Sailing or Motor Boating in limited visibility, whether due to darkness, fog, or other adverse weather conditions, presents unique challenges for mariners. It requires a combination of skill, experience, and adherence to safety protocols to ensure a safe and enjoyable journey. In this article we will delve into the intricacies of sailing in such conditions, providing insights into preparation, navigation, and collision avoidance.

Preparing for sailboat cruising

Preparing for a sailing trip entails a lot of planning. In this blog, we take a look at some of the many safety aspects that a skipper needs to consider before heading off on a cruise.

Propeller care and maintenance

Propellers are complicated and repairs should be done by specialists but owners can carry out checks and some routine maintenance themselves when the boat is in the boatyard. A propeller is critical to a boat’s performance, fuel consumption and ride, so it makes sense to keep a propeller in good working order.

Stern gear maintenance

The stern gear of a boat needs to be checked carefully when the boat is ashore as this is something that can only be done when it is out of the water. The same applies for any maintenance and repairs that may need doing, so it is best to check it all over as soon after an end of season lift out as possible.

Boat plumbing maintenance & troubleshooting

A boat’s fresh water system needs annual maintenance to keep it in good condition. Some boats have far more complex systems than others, with pressurised hot and cold water, associated pumps, an accumulator, calorifier and pressure valves, all to keep a boat owner busy.

Seacock maintenance

If seacocks are always left open and neglected they can eventually seize which will prove a serious threat to boat safety should a connecting hose fail and the seacock refuses to close. There are three main types of seacock – ball valves, cone valves and gate valves.

Boat electrics inspection checklist

With the boat ashore, here are some recommendations for carrying out a boat owner electrics inspection. Safety is always paramount so remember to do the checks with the batteries off. Wearing a head torch helps, make notes as you go and only tackle a repair if you are 100% sure you know what you are doing:

Essential Knots: Reef knot

Essential Knots: Reef knot Use: Tying two ends of rope together, often used for tying up a bundle of loose sail around the boom. Step...

Boat engine fuel system

If engines are installed and serviced correctly then most marine engines are very reliable, but one of the most important parts of the engine to check and service is the fuel system.

Safety Equipment Checklist for Boats

Safety Equipment Checklist for Boats Liferaft line attached The liferaft will not work unless the trigger line is...

Wooden Hulls – Part 1

Traditional wooden boats have a plank on frame construction, a centuries old boat building method that is still in use today. Variations of the traditional method include carvel, clinker and strip planking, which all relate to the way the planking is attached to the frame.